Loading... Please wait...
  • Image 1


Your Price:
$109.37 (You save $130.61)
Calculated at checkout

Product Description


ARROW CLASSROOM SIERRA GRADE 1  (heavy duty) 2 3/4" Backset


Schlage C keyway

Latchbolt operated by lever either side except when key outside locks outside lever. Inside lever always free. Key outside locks unlocks lever only.

cut sheet:   http://www.arrowlock.com/Other/Arrow/Download_Levers/GL_Series/GLSeries.pdf


Housings : Interlocking lever tubes are made from dichromate plated steel. The tubes are attached to the rose insert. This offers fantastic support for a ridged feel without excess movement. Standard bearing sleeves used on most other Arrow lever series are not used on the GL. Requires standard 2-1/8" (53.97mm) bore through door.

OverDrive™: Freewheeling lever action occurs when latch retraction mechanism disengages from lever handle when handle is locked. Built-in stops in the rose insert prevent lever from traveling beyond approximately 70 degrees.

Backset: 2-3/4" (69.85mm) standard.

Door Thickness: 1-3/8" (34.92mm) to 2" (50.8mm).

Latch: Stainless Steel with 1/2" (12.7mm) throw standard. Latch housing is steel, zinc dichromate finish for corrosion resistance. 1" (25.4mm) bore in edge of door is required. Additional latch information below: * Available as parts only

Latch front: Stainless steel. 2-1/4" (57.15mm) x 1-1/8" (28.57mm), 1/8" (3.175mm) in 2" (50.8mm). Strike: Stainless steel. ANSI A115.2, 4-7/8" (123.82mm) x 1-1/4" (31.75mm) curved lip strike standard.

Handing: Non-handed. Levers operate bi-directionally.

Mounting: Thru-bolts within 2-1/8" (53.97 mm) cross bore. Contains two support plates which secure to face of door as well as accept thru–bolts from inside rose assembly.

Exposed Trim: Levers are pressure cast zinc. Streamline rose scalp of brass or bronze complements other series of lever locks.

Rose Inserts: Contain coil spring which is a permanent assembly within rose insert. Inside and outside rose scalps are retained by dimples that create an interference fit with the rose inserts. There are no special retention features added to the rose insert that align the scalp.


Certification BHMA A156.2, Series 4000, Grade 1, UL Listed

Door Thickness Fits 1-3/4" - 2", factory set for 1-3/4"

Strike ANSI 1-1/4" x 4-7/8"

Latch 2-3/4" backset, 1-1/8" front

Handing Non-handed

Warranty 5 years

Arrow GL Series Grade 1 heavy duty levers offer an economically pleasing solution for ADA compliance. The GL solution is designed with the installer in mind, providing fewer subcomponents to allow for an easier to install system. Simply put, the GL Series will be your number one choice when economy is your first priority.


  • ANSI/BHMA A156.2, Series 4000, Grade 1
  • Underwriters Laboratories (UL and CUL) listed for use on 3 hour, A label single swinging doors.
  • Federal Specification FF-H-106C
  • ANSI A117.1 Accessibility Code
  • California State Reference Code–for levers returning to within 1/2" (12.7mm) of door

ADA/Americans with Disabilities Act: Acceptable Door Hardware: Section 4.13.9

Handles, pulls, latches and other operating devices on accessible doors shall have a shape that is easy to grasp with one hand and does not require grasping, tight pinching or twisting of the wrist to operate. Lever operated mechanisms, push-type mechanisms and “U” shaped handles are acceptable designs